OPINIONATED OMARCHY
TROUBLESHOOTING CORPUS
790
RECORDS
790
AUDITED
0
UNCHECKED
2388
SOURCES
LIVE
gpu-drivers low common DISPUTE

Unlock AMD GPU clock, voltage and power controls for LACT or CoreCtrl

omarchyarchendeavouroscachyosmanjaroamddesktopliminegrub
CORRECTED An auditor found the fix wrong or incomplete and rewrote it. · checked against Omarchy omarchy 4.0.4-1 on 2026-10-05
AUDIT NOTE

The kernel-parameter route holds: Arch wiki AMDGPU has the 0x4000 PP_OVERDRIVE_MASK advice, the 0xffffffff warning and the exact printf. LACT 0.10.1 is in extra and its README has the power-profiles-daemon 0.30+ note. The earlier correction's central claim is wrong for Omarchy 4: limine-mkinitcpio-hook 1.38.0 ships /usr/local/bin/mkinitcpio, which runs /usr/bin/mkinitcpio and then, for -P, asks whether to run limine-mkinitcpio and treats an empty answer as yes. LACT's regenerate_initramfs (lact-daemon/src/system.rs) calls run_command("mkinitcpio", ["-P"]) by name with Command::output(), so stdin is null, and systemd's default search path here is /usr/local/bin:/usr/bin. So LACT's button most likely does rebuild the UKI on Omarchy 4, and saying it 'rebuilds nothing' is not supported. I did not press the button or run mkinitcpio. The cause also overstated the power-profiles-daemon conflict: PPD's amdgpu_dpm action is opt-in (action-optin TRUE in ppd-action-amdgpu-dpm.c) and /var/lib/power-profiles-daemon/state.ini on this machine has amdgpu_dpm=false. This machine has no AMD GPU, so the mask arithmetic was checked against the wiki, not sysfs.

The cause above was rewritten on 2026-10-05 to match this note; the fix was corrected by the audit itself.
RISK

Overclocking or undervolting can cause crashes, GPU hangs and in rare cases hardware damage. Setting the full 0xffffffff mask can break suspend and resume. LACT documents recovery from a bad overclock on its wiki: keep that page handy before applying settings at boot.

Symptom

LACT or CoreCtrl shows the GPU but the overclocking, undervolting or power limit controls are greyed out or missing, or writing to /sys/class/drm/card*/device/pp_od_clk_voltage fails. LACT may say overclocking is not enabled.

Cause

amdgpu only exposes manual clock and voltage control in sysfs when the PowerPlay overdrive bit is set in the amdgpu.ppfeaturemask kernel parameter. The default mask leaves PP_OVERDRIVE_MASK (0x4000) off. The Arch wiki warns that setting all 32 bits (0xffffffff) can enable unstable features that cause screen flicker or broken resume, and recommends adding only 0x4000 to the default mask. Omarchy installs power-profiles-daemon 0.30. Its amdgpu_dpm action, which would reset the amdgpu performance level on profile changes, is opt-in and off by default, and LACT 0.7.5 and newer also disables it when it connects to power-profiles-daemon 0.30 or newer.

Fix

Compute a mask that adds only the overdrive bit to your current mask:


printf 'amdgpu.ppfeaturemask=0x%x\n' "$(($(cat /sys/module/amdgpu/parameters/ppfeaturemask) | 0x4000))"

Pick ONE of the two methods below. Do not set the mask both on the kernel command line and in /etc/modprobe.d/.

**Omarchy 4, kernel parameter (recommended, because you can read it back in /proc/cmdline).** Put the printed value in your own drop-in and rebuild the UKI (replace the value with yours):


sudo tee -a /etc/limine-entry-tool.d/zz-local.conf >/dev/null <<'EOF'
KERNEL_CMDLINE[default]+=" amdgpu.ppfeaturemask=0xfff7ffff"
EOF
sudo limine-mkinitcpio && sudo limine-update
sudo reboot

If zz-local.conf already sets amdgpu.ppfeaturemask (for example the gfxoff workaround in amdgpu-idle-freeze-gfxoff-ppfeaturemask), edit that value in place to combine both bits rather than adding a second one.

**Omarchy 4, LACT's "enable overclocking" button.** LACT sees ID_LIKE=arch, writes options amdgpu ppfeaturemask=0x... to /etc/modprobe.d/99-amdgpu-overdrive.conf and runs mkinitcpio -P. On Omarchy 4 that name resolves to /usr/local/bin/mkinitcpio from limine-mkinitcpio-hook, which runs the real mkinitcpio (there are no presets in /etc/mkinitcpio.d/) and then runs limine-mkinitcpio when its prompt gets no answer, as it does from the daemon. That should put the option into the UKI, but it has not been tested here, so check /sys/module/amdgpu/parameters/ppfeaturemask after the reboot. If you used the button and then switch to the kernel parameter, remove LACT's file and rebuild so the UKI does not carry two different masks:


sudo rm -f /etc/modprobe.d/99-amdgpu-overdrive.conf
sudo limine-mkinitcpio

**Plain Arch, GRUB:** add the value to GRUB_CMDLINE_LINUX_DEFAULT in /etc/default/grub and run sudo grub-mkconfig -o /boot/grub/grub.cfg. On plain Arch with mkinitcpio presets, LACT's button also works.

Then install and start LACT:


sudo pacman -S --needed lact
sudo systemctl enable --now lactd

After the reboot, check:


cat /proc/cmdline
printf '0x%x\n' $(( $(cat /sys/module/amdgpu/parameters/ppfeaturemask) & 0x4000 ))   # 0x4000 means overdrive is on

Verify

cat /sys/module/amdgpu/parameters/ppfeaturemask shows the new value, cat /sys/class/drm/card*/device/pp_od_clk_voltage prints clock tables, and LACT's overclocking page is editable.

Sources

amdgpu-overclocking-locked-ppfeaturemask