OPINIONATED OMARCHY
TROUBLESHOOTING CORPUS
790
RECORDS
790
AUDITED
0
UNCHECKED
2388
SOURCES
LIVE
omarchy-core critical occasional DISPUTE

Fix a permanent black screen after install on an older NVIDIA card

omarchyarchnvidiadesktop
CORRECTED An auditor found the fix wrong or incomplete and rewrote it.
AUDIT NOTE

The problem is real but the fix throws away a supported path. Verified in install/hardware/nvidia.sh: Omarchy already handles pre-Turing cards by installing the legacy branch: nvidia-580xx-dkms nvidia-580xx-utils lib32-nvidia-580xx-utils when omarchy-hw-nvidia-without-gsp matches, versus nvidia-open-dkms nvidia-utils for GSP-capable GPUs. All of those are listed in install/omarchy-other.packages. So the first move should be installing the 580xx branch, not ripping NVIDIA out for nouveau. The mkinitcpio guidance repeats the error from the sibling record: Omarchy uses /etc/mkinitcpio.conf.d/nvidia.conf (MODULES+=) and /etc/mkinitcpio.conf.d/omarchy_hooks.conf for the conditional kms removal, not /etc/mkinitcpio.conf. Modesetting is set in /etc/modprobe.d/nvidia.conf, not on the kernel cmdline, so 'drop nvidia_drm.modeset=1 from the kernel cmdline' targets something that is not there. Also GPU generations are conflated: a GT 630 is Fermi/Kepler and needs the 470xx branch, while a GTX 10xx is Pascal and is covered by 580xx. pacman -Rns nvidia-utils can cascade into other packages that depend on it.

The cause above was not rewritten and may still contain the error described. The fix below is the corrected version.
RISK

Removing driver packages and editing mkinitcpio.conf can leave the machine with no working display path at all. Do this from a TTY you can get back to, keep the LTS kernel entry, and note that pacman -Rns nvidia-utils may cascade-remove other packages, so read the transaction list before confirming.

Symptom

Install completes and the machine reboots to a permanent black screen, with no login prompt and sometimes not even a TTY. Common on older NVIDIA cards (Kepler/Maxwell/Pascal era, e.g. GT 630, GTX 10xx) paired with older Intel CPUs.

Cause

Two overlapping causes: (a) modern nvidia/nvidia-open packages no longer support pre-Turing GPUs, since Arch's NVIDIA 590 release dropped Pascal and older and switched the main packages to the Open Kernel Modules. (b) With an unsupported card the DRM device never initialises, so Hyprland cannot start and there is nothing to display.

Fix

Get to a console. If Ctrl + Alt + F2 is dead, reboot, press e on the Limine entry and append nomodeset to the kernel cmdline for a one-off text boot.

Identify the card and let Omarchy's own detector tell you which driver branch you need:


lspci -k | grep -A3 -i vga
lsmod | grep -E 'nvidia|nouveau'
journalctl -b -p err --no-pager | head -50

omarchy-hw-nvidia-gsp && echo "Turing+ -> nvidia-open-dkms"
omarchy-hw-nvidia-without-gsp && echo "pre-Turing -> nvidia-580xx-dkms"

For a pre-Turing card, install the **legacy 580xx branch**. Do not go to nouveau first. This is the path Omarchy's installer itself takes:


# Maxwell / Pascal / Volta (e.g. GTX 9xx, GTX 10xx, Titan V):
sudo env OMARCHY_ALLOW_DIRECT_PACMAN=1 pacman -Syu --needed \
  nvidia-580xx-dkms nvidia-580xx-utils lib32-nvidia-580xx-utils linux-headers
sudo limine-mkinitcpio
sudo reboot

For a Fermi/Kepler card (e.g. GT 630, GTX 6xx/7xx), 580xx does NOT cover it. You need the older legacy branch from the AUR:


yay -S nvidia-470xx-dkms nvidia-470xx-utils
sudo limine-mkinitcpio

Only if no legacy branch supports your card, fall back to nouveau/Mesa:


sudo pacman -Rns nvidia-open-dkms nvidia-utils lib32-nvidia-utils   # review the cascade before confirming
sudo env OMARCHY_ALLOW_DIRECT_PACMAN=1 pacman -Syu --needed mesa lib32-mesa vulkan-nouveau

Then remove Omarchy's NVIDIA drop-ins. These are separate files, NOT edits to /etc/mkinitcpio.conf:


sudo rm -f /etc/mkinitcpio.conf.d/nvidia.conf
sudo rm -f /etc/modprobe.d/nvidia.conf
sudo limine-mkinitcpio
sudo reboot

Leave the kms hook alone. /etc/mkinitcpio.conf.d/omarchy_hooks.conf restores it automatically once nvidia_drm is no longer early-loaded. And do not go hunting for nvidia_drm.modeset=1 on the kernel cmdline. Omarchy sets modesetting via modprobe.d, so it was never there.

Verify

After reboot the login screen appears. lsmod | grep nouveau shows the module loaded and hyprctl monitors lists your display.

Sources

black-screen-after-install-old-nvidia