Recover a GTX 10xx/9xx desktop broken by the NVIDIA 590 upgrade
The cause holds. I fetched the cited Arch news item of 2025-12-20 and read it in full: driver 590 drops Pascal and older, nvidia becomes nvidia-open, nvidia-dkms becomes nvidia-open-dkms, and Pascal users must move to nvidia-580xx-dkms from the AUR. The Arch wiki NVIDIA table (fetched as raw wikitext) lists Volta, Pascal and Maxwell against nvidia-580xx-dkms, status Legacy supported, and the AUR RPC shows nvidia-580xx-dkms, nvidia-580xx-utils and lib32-nvidia-580xx-utils all at 580.178.04-1, maintained and not flagged out of date. Confirmed on this machine by reading /usr/share/omarchy/install/hardware/nvidia.sh: Omarchy 4 picks exactly those three packages when omarchy-hw-nvidia-without-gsp matches, and yay 13.0.1-1 is installed so the AUR step is available. Five defects. First and worst, sudo mkinitcpio -P writes no new boot image on Omarchy 4: /etc/mkinitcpio.d is empty on this machine (zero entries), mkinitcpio takes its presets from that directory (line 25 of /usr/bin/mkinitcpio sets _d_presets to /etc/mkinitcpio.d), the stock kernel hook is replaced by /etc/pacman.d/hooks/90-mkinitcpio-install.hook calling limine-mkinitcpio-install, and /usr/local/bin/mkinitcpio (from limine-mkinitcpio-hook, first in PATH) warns that it does not update Limine boot entries and then prompts interactively. The user reboots into the old UKI with no working driver, which is the exact black screen the danger warns about. The Arch wiki Limine page says plainly to run limine-mkinitcpio instead of mkinitcpio. Second, the env var step is Omarchy 3 advice. I fetched install/config/hardware/nvidia.sh from the master branch and it is the file that appends env = NVD_BACKEND,egl to ~/.config/hypr/envs.conf. On Omarchy 4 there is no envs.conf (confirmed by listing ~/.config/hypr) and /usr/share/omarchy/default/hypr/nvidia.lua already sets NVD_BACKEND to egl for without-GSP cards, pulled in by default/hypr/envs.lua, so the user must add nothing. Third, the pacman -Rdd line always fails: pacman aborts the whole transaction on the first target that is not installed. Confirmed here with pacman -Rp nvidia-open-dkms doesnotexist-pkg-xyz, which exits 1 with error: target not found and removes nothing. The six names in the record conflict with one another so no machine has all six, and the 2>/dev/null hides the only clue. Fourth, package names are stale: nvidia, nvidia-dkms and nvidia-lts 404 on archlinux.org/packages, and nvidia-lts-open never existed. The real LTS package is nvidia-open-lts (extra, 1:615.71.09-2), and the removal list omits nvidia-utils, which nvidia-580xx-utils conflicts with and which nvidia-open-dkms pins at an exact version (both confirmed with pacman -Qi here). Fifth, the verify step cat /sys/module/nvidia_drm/parameters/modeset is Permission denied for an unprivileged user on this machine and needs sudo. Two source problems: https://github.com/basecamp/omarchy/issues/3954 returns a bare 404 and does not redirect (curl -I shows 404 text/plain, while the repo root 301s to omacom), and the master blob URL resolves but points at the Omarchy 3 tree that produced the wrong envs.conf advice. I also add omacom/omarchy#7947, which is open and reports that the 580xx packages are not in the repositories at all, which is why the fix needs yay rather than pacman -S. Not exercised: I have an RTX 3090 (Turing or newer, driver 610.57.04), so I could not install or boot the 580xx branch, could not run limine-mkinitcpio or mkinitcpio, and could not confirm nouveau or NVK performance on Pascal. The NVK hardware floor comes from the Arch wiki Nouveau page, which states Kepler and newer. Severity critical and frequency common are both left as they are: the machine loses its desktop, and the population is every Omarchy 3 or Arch upgrade on a Maxwell, Pascal or Volta card.
pacman -Rdd skips dependency checks. Use it only to break the version pin between nvidia-open-dkms and nvidia-utils, and install the replacement driver in the same session. Do NOT reboot between removing the old driver and installing the new one unless you are comfortable working from a TTY.
A fixed pacman -Rdd package list is itself a trap. Pacman aborts the whole transaction on the first target that is not installed, removes nothing, and says so in one line that is easy to miss. Check what it actually removed before you carry on.
Building the AUR DKMS package needs headers matching every installed kernel. If headers are missing the module is not built, dkms status will say so, and you reboot into a black screen.
On Omarchy 4, sudo mkinitcpio -P is not enough and gives no useful error. /etc/mkinitcpio.d is empty, so there are no presets to process and no new boot image is written. You reboot into the old UKI with the old modules. Run sudo limine-mkinitcpio instead.
If you do end up with no desktop, Omarchy 4's Limine menu carries btrfs snapshots under a Snapshots submenu. Boot the newest snapshot taken before the upgrade rather than reinstalling. Check what the menu holds with limine-list.
Symptom
After a system upgrade (omarchy update on Omarchy 4, sudo pacman -Syu on plain Arch) on a machine with a GTX 1050/1060/1070/1080, GTX 9xx, MX150 or Titan X, the graphical session no longer comes up. You get a black screen, or you land in a TTY. nvidia-smi prints NVIDIA-SMI has failed because it couldn't communicate with the NVIDIA driver. dmesg shows the NVIDIA module refusing to bind to the GPU.
Cause
NVIDIA driver 590 dropped support for Pascal and older GPUs, and Arch simultaneously switched the main packages to the open kernel modules: nvidia became nvidia-open, nvidia-dkms became nvidia-open-dkms, and nvidia-lts became nvidia-open-lts. The open kernel modules need GSP firmware, which arrived with Turing, so they support Turing (GTX 16xx and RTX 20xx) and newer only. On Pascal and older the driver simply fails to load after the upgrade. Note that the Arch news item announcing the change wrote the LTS package name as nvidia-lts-open, but the package Arch actually ships is nvidia-open-lts.
Fix
From a TTY (Ctrl+Alt+F2) or a chroot.
**1. Remove only the mainline NVIDIA packages that are actually installed.** A fixed list does not work: pacman -Rdd aborts the entire transaction on the first name that is not installed and removes nothing, and those package names conflict with each other so no machine has them all.
installed=()
for p in nvidia nvidia-open nvidia-dkms nvidia-open-dkms nvidia-lts nvidia-open-lts \
nvidia-utils lib32-nvidia-utils opencl-nvidia lib32-opencl-nvidia; do
pacman -Qq "$p" &>/dev/null && installed+=("$p")
done
printf '%s\n' "${installed[@]}"
(( ${#installed[@]} )) && sudo pacman -Rdd "${installed[@]}"
-Rdd skips dependency checks. It is needed here only because nvidia-open-dkms pins nvidia-utils to an exact version and nvidia-580xx-utils conflicts with nvidia-utils.
**2. Install headers for every kernel you have installed.**
sudo pacman -S --needed linux-headers # add linux-lts-headers / linux-zen-headers as applicable
**3. Install the legacy proprietary 580xx branch.** It is AUR-only, so plain pacman -S reports target not found (this is what breaks the Omarchy installer in omacom/omarchy#7947). Omarchy ships yay:
yay -S nvidia-580xx-dkms nvidia-580xx-utils lib32-nvidia-580xx-utils
nvidia-580xx-utils provides nvidia-utils, which is what hyprland, libglvnd and steam depend on, so those stay satisfied.
**4. Rebuild the boot image.** The command differs by distro, and getting it wrong is what leaves you at a black screen:
# Omarchy 4: /etc/mkinitcpio.d is EMPTY and the system boots a UKI at
# /boot/EFI/Linux/omarchy_linux.efi. `mkinitcpio -P` has no presets to process,
# so it builds nothing and the UKI keeps the old modules.
sudo limine-mkinitcpio
# Plain Arch, where kernel packages drop a preset in /etc/mkinitcpio.d:
sudo mkinitcpio -P
reboot
Omarchy's installer picks these same three packages for Maxwell, Pascal and Volta. See /usr/share/omarchy/install/hardware/nvidia.sh and its detector /usr/share/omarchy/bin/omarchy-hw-nvidia-without-gsp, which matches NVIDIA PCI device IDs from 0x1340 up to but not including 0x1e00.
These cards also need NVD_BACKEND=egl rather than direct. Where that goes depends on the version:
- **Omarchy 4 sets it for you** at every session start, from
/usr/share/omarchy/default/hypr/nvidia.lua, keyed on the same detector and loaded bydefault/hypr/envs.lua. Add nothing. Hardcoding it yourself only risks pinning the wrong value if you later change cards. - **Omarchy 3** wrote it to
~/.config/hypr/envs.confin hyprlang:
env = NVD_BACKEND,egl
env = __GLX_VENDOR_LIBRARY_NAME,nvidia
- **Plain Arch on Hyprland 0.55 or newer**, in your own Lua config:
hl.env("NVD_BACKEND", "egl")
hl.env("__GLX_VENDOR_LIBRARY_NAME", "nvidia")
If you would rather not touch the AUR, the fully open nouveau and NVK stack (mesa plus vulkan-nouveau) covers Kepler and newer, so it does run on these cards. Expect a large performance cost, and note that the Arch wiki still marks NVK a work in progress.
Verify
nvidia-smi prints a driver version in the 580.x series and lists your GPU. sudo cat /sys/module/nvidia_drm/parameters/modeset returns Y (that file is root-readable only, so it needs sudo). dkms status shows the nvidia module installed against your running kernel. Hyprland starts.
Sources
- https://archlinux.org/news/nvidia-590-driver-drops-pascal-support-main-packages-switch-to-open-kernel-modules/
- https://wiki.archlinux.org/title/NVIDIA
- https://wiki.archlinux.org/title/Nouveau
- https://wiki.archlinux.org/title/Limine
- https://wiki.archlinux.org/title/Mkinitcpio
- https://aur.archlinux.org/packages/nvidia-580xx-dkms
- https://github.com/omacom/omarchy/issues/3954
- https://github.com/omacom/omarchy/issues/7947
- https://github.com/omacom/omarchy/blob/quattro/install/hardware/nvidia.sh