High-refresh monitor on NVIDIA tops out at 120 Hz, and higher modes give 'No Signal'
Arch wiki NVIDIA/Troubleshooting 'Refresh-rate limited to 120Hz' gives nvidia-modeset.hdmi_deepcolor=0 and the HDR caveat, and says newer drivers 'after 550xx' waste bandwidth on 8 bpc outputs. BBS 302969 confirms the 120 Hz ceiling on HDMI with the NVIDIA driver, that nouveau, Windows and DisplayPort reach full refresh, and the poster who found the fix says deep colour was off by default on 550.144.03 and enabled from 555, so 'since the 550 driver series' is wrong by one series. open-gpu-kernel-modules nvidia-modeset-linux.c has static bool hdmi_deepcolor = true, module_param 0444. On this machine modinfo nvidia_modeset (610.57.04) lists hdmi_deepcolor:bool, /sys/module/nvidia_modeset/parameters/hdmi_deepcolor is root-only (so sudo cat is right), nvidia_modeset is in /etc/mkinitcpio.conf.d/nvidia.conf, and ~/.config/hypr/monitors.lua uses the same hl.monitor({ output, mode, position, scale }) form. Only the cause needed correcting. The parameter was not applied here.
Deep colour is required for HDR and 10-bit output over HDMI, so this parameter disables HDR on HDMI outputs. Remove it if you need HDR and use DisplayPort instead. The parameter is read only when the module loads, so a reboot is required. The usual Omarchy drop-in cautions apply: += not =, and check df -h /boot before limine-mkinitcpio.
Symptom
A 144, 165 or 180 Hz monitor connected to an NVIDIA GPU, usually over HDMI 2.0, only works up to 120 Hz. Selecting a higher mode turns the screen black and the monitor reports No Signal, then it falls back to 120 Hz or stays black. The same monitor and cable reach full refresh on nouveau, on Windows, or over DisplayPort.
Cause
From the 555 driver series onward, the NVIDIA driver enables HDMI deep colour by default (it was off on 550.144.03, according to the user who found the fix in the linked BBS thread), and it appears to spend bandwidth on deep colour even for 8 bits per channel outputs. The Arch wiki describes this as newer drivers wasting bandwidth on 8 bpc outputs, which pushes the higher-refresh modes past the link's limits, so the mode fails to apply. The workaround is the nvidia-modeset module parameter hdmi_deepcolor=0, which exists on current drivers: modinfo -p nvidia_modeset on 610.57.04 lists hdmi_deepcolor, and its default is on. Users in the BBS thread confirm 120 Hz is the ceiling on HDMI with the NVIDIA driver, and that DisplayPort avoids it.
Fix
**Quickest test:** use DisplayPort if the monitor has it.
**Kernel parameter, Omarchy 4.** nvidia_modeset is loaded from the initramfs, so put the parameter on the command line through your own drop-in:
sudo tee -a /etc/limine-entry-tool.d/zz-local.conf >/dev/null <<'EOF'
# `+=` appends. A bare `=` would wipe Omarchy's own defaults.
KERNEL_CMDLINE[default]+=" nvidia_modeset.hdmi_deepcolor=0"
EOF
sudo limine-mkinitcpio && sudo limine-update && sudo reboot
**Plain Arch:** add nvidia_modeset.hdmi_deepcolor=0 to the kernel command line (systemd-boot options, or GRUB_CMDLINE_LINUX_DEFAULT then sudo grub-mkconfig -o /boot/grub/grub.cfg). The alternative is options nvidia_modeset hdmi_deepcolor=0 in /etc/modprobe.d/nvidia-hdmi.conf followed by sudo mkinitcpio -P.
Then set the mode. On Omarchy 4, edit ~/.config/hypr/monitors.lua:
hl.monitor({ output = "HDMI-A-1", mode = "1920x1080@180", position = "auto", scale = 1 })
Verify
sudo cat /sys/module/nvidia_modeset/parameters/hdmi_deepcolor # N once applied
hyprctl monitors | grep -A1 HDMI
hyprctl monitors reports the higher refresh rate, for example 1920x1080@180.00000, and the monitor's OSD agrees.